Before the Membrane Goes Down: What a Waterproofer Should Check First
Good waterproofing starts before the membrane goes down. Here’s what to check first — from substrate preparation and drainage to detailing, sequencing and system selection.
Nov 22, 2026
Written by
Chris BarnesA good waterproofing job does not start when the lid comes off the membrane.
It starts much earlier.
Before any waterproofing is applied, there are decisions to make about the substrate, falls, drainage, penetrations, junctions, sequencing and the system being used. If those things are not right, simply applying more membrane is unlikely to solve the problem.
One of the most important habits a waterproofer can develop is learning to stop and properly assess the job before starting.
Is the substrate actually ready?
The first question should not be “What membrane am I using?”
It should be:
“What am I waterproofing over, and is it ready?”
Look at the condition of the substrate. Is it sound? Clean? Stable? Dry enough for the proposed system? Are there cracks, voids, contaminants or areas that still need repair?
A membrane is only one part of the system. If the surface beneath it is poorly prepared, unstable or unsuitable, the waterproofing is already starting from a weak position.
Preparation is not the boring part before the real work starts.
Preparation is part of the waterproofing.
Check the falls and drainage before you inherit the problem
Falls, drainage points and water movement should be considered before waterproofing begins.
Where is the water supposed to go?
Are the falls suitable for the area?
Is the waste or drainage point positioned and installed correctly?
Are there low areas where water could collect?
If something is wrong, identify it before applying the waterproofing.
Once you waterproof over an existing problem, it becomes much harder to separate where one trade's responsibility finished and yours began.
A capable waterproofer learns to recognise when the job is not ready and has the confidence to raise it.
Look at the details — not just the big surfaces
Large flat areas are rarely the most complicated part of waterproofing.
The risk is often in the details.
Corners. Junctions. Penetrations. Waterstops. Doorways. Thresholds. Drains. Changes in substrate. Interfaces with other building elements.
Before starting, walk the job and identify these areas.
Ask yourself:
How is this detail going to work once I reach it?
If you do not know, that is the time to find out — not when you are halfway through applying the membrane.
Make sure the system suits the job
Product selection should be more than grabbing the system you normally use.
Consider the location, substrate, exposure, construction detail and what will happen over the waterproofing once you finish.
Read the relevant product information and understand how the components are intended to work together.
Primer, reinforcement, sealants, bond breakers, membrane and other components should form part of a considered system rather than a collection of products chosen independently.
Sometimes the right question is not:
“Can I use this product?”
It is:
“Is this the right system for this particular job?”
Think about the trades around you
Waterproofing rarely happens in isolation.
Plumbers, carpenters, concreters, plasterers, tilers, builders and other trades can all affect the area before or after the waterproofing is installed.
Ask what still needs to happen.
Will something be fixed through the membrane later?
Is another trade returning to the area?
Are there penetrations that have not yet been completed?
Is the tiler expecting something different from what you are preparing?
A five-minute conversation before starting can sometimes prevent a much bigger conversation later.
Document what you see
Good documentation protects more than the job.
It helps create professional habits.
Take clear photographs before starting, particularly where there are unusual conditions or existing issues.
Record important discussions and agreed changes where appropriate.
Keep product and job information organised.
Then document the waterproofing as it progresses, especially details that will eventually disappear beneath screeds, tiles or other finishes.
Once the work is covered, those photographs may be the only record of what was actually installed.
Know when to stop and ask
Perhaps one of the most important capabilities a waterproofer can develop is knowing when not to keep going.
There will be jobs where something does not look right.
You may find a detail you have never dealt with before. The substrate may not be what you expected. Two pieces of information may appear to conflict. The proposed construction might simply not make sense.
Stopping to ask a question is not a sign that you do not know what you are doing.
Continuing when you are unsure can be a much bigger problem.
Experience does not mean knowing every answer.
Experience is also knowing when you need another one.
Better waterproofing starts before waterproofing
Applying membrane is an important skill.
But becoming a capable waterproofer requires more than application.
It means learning to assess the job, identify risk, understand the system, communicate with the people around you and make informed decisions before the waterproofing disappears beneath the next stage of construction.
Before you open the membrane, ask yourself one simple question:
Is this job actually ready to waterproof?
If the answer is not clearly yes, work out why before you start.
Need another waterproofing perspective?
Sometimes you simply want another experienced person to talk a job through with.
Your Waterproofing Coach provides practical waterproofing advice, coaching and on-site support to help you understand the detail, work through the options and make better-informed decisions.
Talk to Your Waterproofing Coach- www.yourwaterpoofingcoach.com.au